The IAP boots with the factory default settings. Many people mistakenly think that this command can be used to reset an AP back to factory default, but that is not true. At Aruba, we believe that the most dynamic customer experiences happen at the Edge. Call a Specialist Today! I have some AP515s that shipped as IAPs.
When sourcing the full 5W power budget to such a device, the incremental (worst-case) power consumption for the AP is up to 6.5W.
510 Series Data Sheet Hi, I have some AP515s that shipped as IAPs. Add Cosmetic Snap-On Cover (AP-515 Only, Optional), High performance 802.11ax enterprise access points for campus deployments, Aruba Instant On 1930 8G Class 4 PoE 2SFP 124W Switch, Aruba Instant On 1930 24G 4SFP/SFP+ Switch, Aruba Instant On 1930 24G Class 4 PoE 4SFP/SFP+ 195W Switch, Aruba Instant On 1930 24G Class 4 PoE 4SFP/SFP+ 370W Switch, Aruba Instant On 1930 48G 4SFP/SFP+ Switch, Aruba Instant On 1930 48G Class 4 PoE 4SFP/SFP+ 370W Switch, Aruba Instant On for Online Education for Teachers and Parents, Aruba AP-510 Series Access Points Datasheet. Dimensions/weight (AP-515; unit, excluding mount bracket): (H) 46mm x (W) 200mm x (D) 200mm (1.8″ x 7.9″ x 7.9″), (H) 72mm x (W) 230mm x (D) 220mm (2.8″ x 9.1″ x 9.1″), Temperature: 0°C to +50°C / +32°F to +122°F, AP is plenum rated for use in air-handling spaces, Temperature: -40°C to +70°C / -40F to +158°F, ETS 300 019 classes 1.2 and 2.3 environments.
The Aruba 510 Series Campus Access Points (AP-514 and AP-515) are high-performance, multi-radio wireless, devices that can be deployed in either controller-based (ArubaOS) or controllerless (Aruba Instant) network, environments. Free Shipping! Press and hold the reset button using a small, narrow object, such as a paper clip. Power on the IAP and keep the reset button pressed. For more country-specific regulatory information and approvals, please see your Aruba representative. 2. If you need to reset your Aruba AP's to factory defualt it's really simple. All numbers above are without an external USB device connected. Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): Note: conducted transmit power levels exclude antenna gain. Site Terms and Privacy Policy, 6. Release the reset button 15 seconds after the power cycle is complete.
If I purge/save/reset and AP and also remove its old record from a controller, when I plug the AP back into the network and the controller adopts it, it comes back with its old config and name again instead of just the mac address like a new AP would. To restore an AP-80 to factory defaults, we must use the button that is inside the AP. In this case, we can simply go to the controller WebUI AP provisioning page and wipe out all the parameters that have been statically configured. Worst-case internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 1.3dB in 2.4GHz and 1.7dB in 5GHz. Virtual Graffiti Inc, an authorized Aruba Networks reseller. © Copyright 2020 Hewlett Packard Enterprise Development LPAll Rights Reserved. Release the reset button on the access point after 15 seconds. If by mistake you load a code older than 2.5, the AP may not work and you might have to recover the AP. Since ArubaOS 8.5 the default credential is admin / Serial Number of your IAP. Community Home > Discuss > Technology > Wireless Access > Aruba AP 305 factory reset using console Wireless Access This community is currently in … The 510 series supports maximum data rates of 4.8Gbps in the 5GHz band and 575Mbps in the 2.4GHz band (for an aggregate peak data rate of 5.4Gbps).