An automated review of this page attempts to determine its readability in English (US). We also offer a large variety of clock barrels such as Hermle clock barrels and Kieninger clock barrels. Square the radius of the inside of the barrel and multiply by Pi (3.1416). As mentioned before, the Générale Ressorts catalog is the largest source of mainspring info out there.
To put the spring back into the clamp is to do the opposite of the removal.
During a service, there are two options for the mainspring. Perhaps he or she installed the wrong one.
The hole end mainspring winder will again make this safer and easier. The NAWCC is dedicated to providing association services, promoting interest in and encouraging the collecting of clocks and watches including disseminating knowledge of the same.
When a mainspring sticks to itself then it can’t put out the power it used to because of the friction. © 2020 Clockworks.
Just apply just enough pressure to see it snap into place. Please be aware that although it offers this info, it’s not a platform that concentrates on watchmaking.
The installed rivet should be tight and secure but at the same time letting the click move back and forth freely before the click spring's pressure is reapplied.
124.
Unwind the spring without the holder now until it is completely unwound then it can be cleaned in solution and greased with mainspring grease. I can tell you I have done it this way many times and have never gotten smacked by a spring. Clock Parts > Mainspring There are basically two types of clock mainsprings. Movement No. Alarm spring for Tot.
4.5² x 3.1416 = 63.62 (area of the barrel). Time to look at the gears (AKA wheels) and see if the teeth are bent or worse, BROKE.
If the clock is an American 8 day time strike movement chances are the dimensions of the spring is ¾ x .018 x 96”.
The site is up but some features are still being tuned. The measurements you need are the height, the thickness, the length, and the inside diameter of the barrel. Movement No. The also come with an assortment of chucks that go into the mainspring barrels when working with hole end mainsprings. We have a chart of all the Loop End Mainspring sizes available to be purchased new.
Time spring for Brownie, Tattoo, Junior, Artlarm, O.M. Wear a full suit of armor doing this. Riveting Click rivets that have come loose happen for a variety of reasons. Time, Strike and Chime spring for Chime clocks.
On rare occasions the clock requires a strange sized spring that is not available.
4582, No.
He's also a big fan of science fiction, baseball, and comics.
Let me know in the comments below.
So, a mainspring doesn’t have to be replaced with every service.
1.5² x 3.1416 = 7.07 (area of the arbor hub).
You can use this book to identify movements and to look up info such as the hole diameters of the hands and, you guessed it, the dimensions of the mainspring. I hold the entire operation as far from my body as possible, then yank the spring out with the pliers.
Make sure you order a mainspring with the right attachment.
One downside is that it doesn’t merely list the metric measurements. CMH 160.6 5/8 x.016 x.59 Hole Time and Alarm spring for all 8-Day Alarm Clocks.
The mainspring that has been cut down so it is shorter only means the clock will not run as long, if it is an 8 day clock then it might only last 7 days instead. Just take control of handling mainsprings with precaution and confidence, and you will find that they are an easy obstacle to conquer.
It is really an arbor, but the skinny end of the arbor that sticks throughout the plate is called a pivot in clock world. Replacing teeth is covered later on.
Also for 337 to 340 Movements. This tool takes the fear from clock repair. There’s a problem with this method though. And I mean low heat, if you get this sucker to hot it will break when you wind it and that would be a lot of wasted effort. After letting the power of any other springs so they are harmless in the clamps, disassemble the movement.
You really do not want to get whacked by one of the clock mainsprings, they can hurt. That's easy! Time Spring for Amazone, Clatter, Flash, Pirate, Presto, Princess, Racket, Rally, Repeater, Startle, Tattler, Trolley and Trump. With the spring clamped down good, drill your new hole. Time and Strike Spring for 30 Hour Athens, Time and Strike Spring for Sharon (A-200). Then unwind the spring into its holder. CML 160.1 5/8 x.014 x 70 Hole For 8-Day Marine and Ormond Clocks. Some older watches require a mainspring with a special bridle such as a T-end or an end with a hole.
Mainsprings are serious business, they pack a punch, so please do not take them too lightly and end up getting smacked by one. To put the new spring into a barrel is easier because the new springs come already wound up. Just turn the arbor the opposite way of the spring winding direction, and you will see the nub pop out of the mainspring hole.
If you have a 31-day clock, or a Korean/Chinese clock, or a commonly produced early American time & strike movement, it usually takes a number 6 or 7. Now you bring the tail stock of the mainspring machine up to the other side of the barrels arbor, set the machine to wind, hold the barrel with your hands (using gloves) and start winding up the spring. Contact the Webmaster for perceived copyright infringement (DMCA Registration Number 1010287). You never know how long the mainspring has been inside the watch and micro fractures are nearly impossible to spot. Book Review: “100+ No BS Watch Tips” by Anthony L.
How do you choose the right mainspring? In general, most larger German movements take a number 8 key but some take a number 4. If you do not have confidence in doing this, buy a new spring (they do not cost much) or get a hole end mainspring winder tool from us here at Clockworks. It consists of the main winding component that has a switch to flip from wind to unwind. 123. If you need to calculate the length of a mainspring, you can use the following formula: Length of the mainspring when the inside diameter of the barrel is 9 mm, the diameter of the barrel hub is 3 mm, and the thickness of the mainspring is 0.11 mm. When the spring is wound enough to get the holder in place, insert the holder over the spring leaving some of the springs length out of the holder where the hole end is. We've already sent your tracking #, and all you have to do is track it. Arbors are the first to be straightened with whatever means you have. 4601 to No.
113. Mainsprings can do alot of damage to a clockmaker. The arbor that connects to the center of the spring is only connected by a nub hooked inside the hole at the beginning of the mainspring.
You can find them on the Cousins website, for example, but you’ll need to create an account to download documents. If the unwound spring is a foot or more in diameter (in a American 8 day time strike movement taking a ¾ x .018 x 96 spring) than it should be good to use after it is cleaned.
The mainspring does have less power sometimes when it is fully wound then it does say ¾ of the way wound. People have lost eyes, cut there gut open, and other horrible things from attempting to wind or unwind mainsprings by hand. Clock Mainspring Warning. You wouldn’t be the first person (or the last) who orders an automatic mainspring for a manual winding watch. The solution goes on some cloth and then rubbed on both sides of the spring. Alarm spring for Amazone, Flash, Pirate, Presto, Racket, Rally and Tourist. After you’ve written down the dimensions, you can use them to search for the correct mainspring online. 4584, No.
Alarm spring for Royal, Sunrise, Thrift, Turn-Out, Twin, Vigilent and No-Sleep. The page contains roughly. Make sure there are no ridges on the pliers because if you mare up the pivot then when its back in the clock it will eat away at the brass plate. This can be done by hand, but is again, moderately dangerous.
One of those is Ranfft.
If the rivet hole is oblong instead of round, make the hole round again with a broach or file. You have about one shot at straightening the pivot, if the pivot is bent this way or that way too much it will break. One of them is Bestfit.
Let us show you where it's at. There’s one problem with this method though. Mainspring over-wind myth Clocks can’t be over-wound. Alarm spring for Bi-Nite, Tornado, Wake-up No.
Time spring for Carriage.